The Minikin is back the all new Minikin 2! The Minikin 2 is powered by a GX-180-HT/UT chip which incorporates the same battery power saving capabilities as its predecessors but features a new wattage cap of 180 watts and touch screen support!
The Minikin 2 utilizes newly updated firmware which displays the following information on its LED screen: Individual battery charge, resistance of the atomizers, volts being used to fire at desired wattage, a puff counter, the duration of the fire, and which mode you are in.
The Minikin 2 features a redesigned body that was designed to be exceptionally comfortable to hold. The asMODus logo has been re-positioned to the back of the device and the USB port has been moved the front of the device as the battery door has been remodeled to add magnetic closure. 15 vent holes have been added to the base of the device which allows for maximized heat dissipation.
Using the device: Unlocking the touch screen is done by simply sliding your finger down the screen. Touching the wattage will allow you to change the wattage using the "+" and "-" buttons that appear on the screen. Pressing the fire button will set the wattage and take you back to the main screen. The menu of the device is accessed by pressing the firing mode when the screen is unlocked. Within the menu you can check the resistance, select a mode, and enter the set up.
Checking resistance: Once in the main menu, clicking the "Res" button enters you into the resistance menu. On this screen you will see "Set Res" on the top and on the bottom you will see a "CHECK" button. By pressing the "CHECK" button , it will give you a resistance and "YES" and "NO" buttons will appear. Pressing "YES" will take you back to the main menu with your resistance set. Pressing "NO" will cause "+" and "-" buttons to appear which allow you to manually change your resistance. NOTE: The manual changing of resistance only applies when using a temperature control mode.
Picking a mode: In the main menu, the 2nd option found is called "Mode". By pressing "Mode" you will enter a mode selection menu that allows you to choose which mode to fire the device in. You will see "PWR" which is your standard variable wattage mode and within that mode you will see two different options: "W" Power which is wattage mode, and a new mode called "Curve". "Curve" is a unique firing mode within traditional power mode that manually imitates the abilities of temperature control by setting 5 different wattage over time presets. For example you can set the device to fire at 80W for .5 seconds then 90W for 0.5 seconds then 75W for 0.5 seconds (for up to 5 different presets). Doing this will run through your presets in a cycle for an extremely fine tuned vaping experience. Wattage in "Curve" can be adjusted in 0.1 watt increments and seconds can be adjusted in .1 second increments. The other options found in the mode selection screen are "Coil" which is used to select which type of wire you are firing against (supports Ni200, SS316, SS317, and Ti), and then "TCR" and "TFR" modes.
Using set up: The last option in the main menu is called "Set Up". In the "Set Up" menu you will see three different pictures. The first one (which looks like a light) controls the brightness of the screen. The screen can be adjusted on a scale of 1 - 10 based on user preference. The 2nd option (which looks like a piece of paper) is used to set a puff limit. This sets a maximum number of puffs that can be taken if you are trying to limit and monitor the amount that you vape. If you try to fire the device and have exceeded your maximum puffs, a warning symbol along with the text of "PUFF LIMIT" will display on the screen and the device will not fire. Setting the limit to 0000 will not set a maximum number of puffs but will still record the amount of puffs taken. The last option (which looks like a garage can) wipes your puffs so can have a fresh gauge of how much the device is being used.
- Requires two 18650 sized batteries
- Touch screen type: Capacitive screen
- Wattage range: 5.0 - 180.0W
- Wattage range (TC Mode): 5.0 - 120.0W Atomizer ohm range: 0.1 - 2.5 ohm
- Max output voltage: 7.5V
- Peek output current: 45A
- Temperature control range: 212° - 572°F / 100°C - 300°C
- Charging parameters: DC 5V/1A Upgradeable system
- NOTE: Due to the sensitive materials used to create the special edition colors, such as chrome and gold, they are fingerprint and scratch magnets. Any aesthetic damages or imperfections are not covered under warranty.
Which strength e-liquid should I choose?
This depends on how powerful your machine is. If you run your machine under 20 watts or on a coil rated above 1.2 Ohms, then you might need a higher nicotine dosage in your e-liquid. The higher the wattage of your machine, the less nicotine you need. So somebody using a typical 0.5 Ohm coil running it at about 35 watts will probably be fine with a 3mg.
Which coil should I use?
Most eCig manufacturers normally produce a selection of different coils for each of their devices. The power of a coil is measured in Ohms. The lower the Ohms, the more power that coil requires in order to get to the right temperature. If your looking for big vapour, then you would use a coil rated 0.5 Ohms or lower. If you wanted a coil that was good for smoking like a cigarette, then anything above 1.2 Ohms will be fine. Coils with higher Ohm ratings require less power and produce less vapour.
What wattage should I set my device to?
This depends completely on the coil you are using. As discussed above, there are many different types of coils, each with a recommended minimum and maximum wattage.
Why is my device leaking?
There are normally two main reasons why this could be happening.
1) You are running the coil too low. Not giving the coil enough power means it can't turn the liquid into vapour, resulting in flooding or leaking.
2) You are using a powerful coil and puffing on it like a cigarette. Coils rated at 0.5 Ohms or lower are specifically designed for Direct Lung vaping.
Why do i get a burning taste?
This is normally a sign that the coil is ready to be replaced. This will also happen if you let your juice run too low.
Why must I Prime my coil?
Priming your coil avoids any unwanted burning tastes when firing up a new coil for the first time. To prime a coil, simply put 4-5 drops of e-liquid into THE TOP before firing it up. The e-liquid will soak into the cotton and this will help you avoid any undesired results.
Do I get a warranty?
JuiceShop offers a full 28 day in house warranty on all our hardware. Should you experience any issues with a device purchased from us, then please contact us withing the 28 day period. For returns after 28 days, please refer to the manufacturers return procedure.
If you wish to exchange a product, the item must still be in its original unopened state.
We can not accept returns on e-liquids.
ALL RETURNS MUST BE ACCOMPANIED WITH THE ORIGINAL RECEIPT OF SALE.