WISMEC Reuleaux RX2/3 Mod
- Availability: In Stock
- Brand: WISMEC
- Product Code: RX2/3
- Reward Points: 175
- Price in reward points: 3499
Reuleaux RX2/3, an updated version of Reuleaux series, designed by JayBo, features the replaceable back cover for two or three cells. The high power output of 150W or 200W is available for your preference. Powerful yet intelligent, the equipped variable temperature control function and upgradeable firmware with custom logo will make your device much attractive and popular. Moreover, there are multiple fashionable colors for your options.
Replaceable Back Cover: Through the battery back cover lock button, you can replace the back cover for two or three cells to your preference.
Optional High Power Output: With two cells, the maximum output power is 150W while the output power reaches 200W with three cells. And the maximum output voltage is 6V and 9V respectively.
Variable Temperature Control System: Equipped with optional VW, TC-Ni, TC-Ti, TC-SS and TCR mode, the device will provide you with different vaping experiences.
Reverse Polarity Protection: Reverse polarity protection can be successfully achieved by the application of special battery anti reverse circuit in the circuit board.
Spring Loaded 510 Connector: The exquisite stainless steel spring loaded 510 connector makes the device much wear-resisting and adaptable.
Upgradeable Firmware with Custom Logo: By connecting the device with a computer through the micro USB port, you can download the file to add the custom logo to your Reuleaux RX2/3 and make the device always up-to-date.
It is better to take out the cells and charge them through external charger. You can also charge the device by connecting it with a computer or a wall adapter via USB cable.
- Size: 40.2*34.5*88.7mm (for 2 cells)
- Size: 40.2*50.1*88.7mm (for 3 cells)
- Thread Type: 510 spring loaded thread
- Cell type: High-rate 18650 cell
- Cell type: (discharging current should be above 25A)
- Output Mode: VW/TC-Ni/TC-Ti/TC-SS/TCR Mode
- Output Wattage: 1-150W (for 2 cells)/1-200W (for 3 cells)
- Resistance Range: 0.05-1.5ohm for TC modes
- Resistance Range:0.1-3.5ohm for VW mode
- Temperature Range: 100-315°C/ 200-600°F (TC modes)
- Reuleaux RX2/3 (no cells)
- Back cover (for 2 cells)
- USB Cable
- User Manual
- Warning Card
- User manual
Which strength e-liquid should I choose?
This depends on how powerful your machine is. If you run your machine under 20 watts or on a coil rated above 1.2 Ohms, then you might need a higher nicotine dosage in your e-liquid. The higher the wattage of your machine, the less nicotine you need. So somebody using a typical 0.5 Ohm coil running it at about 35 watts will probably be fine with a 3mg.
Which coil should I use?
Most eCig manufacturers normally produce a selection of different coils for each of their devices. The power of a coil is measured in Ohms. The lower the Ohms, the more power that coil requires in order to get to the right temperature. If your looking for big vapour, then you would use a coil rated 0.5 Ohms or lower. If you wanted a coil that was good for smoking like a cigarette, then anything above 1.2 Ohms will be fine. Coils with higher Ohm ratings require less power and produce less vapour.
What wattage should I set my device to?
This depends completely on the coil you are using. As discussed above, there are many different types of coils, each with a recommended minimum and maximum wattage.
Why is my device leaking?
There are normally two main reasons why this could be happening.
1) You are running the coil too low. Not giving the coil enough power means it can't turn the liquid into vapour, resulting in flooding or leaking.
2) You are using a powerful coil and puffing on it like a cigarette. Coils rated at 0.5 Ohms or lower are specifically designed for Direct Lung vaping.
Why do i get a burning taste?
This is normally a sign that the coil is ready to be replaced. This will also happen if you let your juice run too low.
Why must I Prime my coil?
Priming your coil avoids any unwanted burning tastes when firing up a new coil for the first time. To prime a coil, simply put 4-5 drops of e-liquid into THE TOP before firing it up. The e-liquid will soak into the cotton and this will help you avoid any undesired results.
Do I get a warranty?
JuiceShop offers a full 28 day in house warranty on all our hardware. Should you experience any issues with a device purchased from us, then please contact us withing the 28 day period. For returns after 28 days, please refer to the manufacturers return procedure.
If you wish to exchange a product, the item must still be in its original unopened state.
We can not accept returns on e-liquids.
ALL RETURNS MUST BE ACCOMPANIED WITH THE ORIGINAL RECEIPT OF SALE.